code Solenoide

Rotabator.ino

@@ -0,0 +1,41 @@
+ /*
+  Blink
+ 
+  Turns an LED on for one second, then off for one second, repeatedly.
+ 
+  Most Arduinos have an on-board LED you can control. On the UNO, MEGA and ZERO
+  it is attached to digital pin 13, on MKR1000 on pin 6. LED_BUILTIN is set to
+  the correct LED pin independent of which board is used.
+  If you want to know what pin the on-board LED is connected to on your Arduino
+  model, check the Technical Specs of your board at:
+  https://www.arduino.cc/en/Main/Products
+ 
+  modified 8 May 2014
+  by Scott Fitzgerald
+  modified 2 Sep 2016
+  by Arturo Guadalupi
+  modified 8 Sep 2016
+  by Colby Newman
+ 
+  This example code is in the public domain.
+ 
+  https://www.arduino.cc/en/Tutorial/BuiltInExamples/Blink
+*/
+ 
+// the setup function runs once when you press reset or power the board
+void setup() {
+  // initialize digital pin LED_BUILTIN as an output.
+  pinMode(LED_BUILTIN, OUTPUT);
+}
+ 
+// the loop function runs over and over again forever
+void loop() {
+  digitalWrite(LED_BUILTIN, HIGH);   
+// turn the LED on (HIGH is the voltage level)
+  delay(1000);                       
+// wait for a second
+  digitalWrite(LED_BUILTIN, LOW);    
+// turn the LED off by making the voltage LOW
+  delay(1000);                      
+ // wait for a second
+}

sketch-rotabators.ino

@@ -1,78 +0,0 @@
- /*
- * Library: https://github.com/bolderflight/MPU9250
-Basic_I2C.ino
-Brian R Taylor
-brian.taylor@bolderflight.com
-
-Copyright (c) 2017 Bolder Flight Systems
-
-Permission is hereby granted, free of charge, to any person obtaining a copy of this software 
-and associated documentation files (the "Software"), to deal in the Software without restriction, 
-including without limitation the rights to use, copy, modify, merge, publish, distribute, 
-sublicense, and/or sell copies of the Software, and to permit persons to whom the Software is 
-furnished to do so, subject to the following conditions:
-
-The above copyright notice and this permission notice shall be included in all copies or 
-substantial portions of the Software.
-
-THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING 
-BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND 
-NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, 
-DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, 
-OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.
-*/
-/*
- * Updated by Ahmad Shamshiri on July 09, 2018 for Robojax.com
- * in Ajax, Ontario, Canada
- * watch instrucion video for this code: 
-For this sketch you need to connect:
-VCC to 5V and GND to GND of Arduino
-SDA to A4 and SCL to A5
-
-S20A is 3.3V voltage regulator MIC5205-3.3BM5
-*/
-
-#include "MPU9250.h"
-#include "AccelStepper.h"
-
-float biai = 1.25;
-
-// an MPU9250 object with the MPU-9250 sensor on I2C bus 0 with address 0x68
-MPU9250 IMU(Wire,0x68);
-int status;
-AccelStepper stepper;
-
-void setup() {
-  // serial to display data
-  Serial.begin(115200);
-  stepper.setMaxSpeed(1700);
-  stepper.setSpeed(1700);
-  while(!Serial) {}
-
-  // start communication with IMU 
-  status = IMU.begin();
-  if (status < 0) {
-    Serial.println("IMU initialization unsuccessful");
-    Serial.println("Check IMU wiring or try cycling power");
-    Serial.print("Status: ");
-    Serial.println(status);
-    while(1) {}
-  }
-}
-
-void loop() {
-  // read the sensor
-  IMU.readSensor();
-  stepper.runSpeed();
-  // display the data
-  Serial.print("AccelX: ");
-  Serial.print(IMU.getAccelX_mss(),2);
-  Serial.print("	");
-  Serial.print("AccelY: ");  
-  Serial.print(IMU.getAccelY_mss(),2);
-  Serial.print("	");
-  Serial.print("AccelZ: ");  
-  Serial.println(IMU.getAccelZ_mss() + biai,2);
-
-  delay(200);
-}