Rotabator.ino

@@ -1,44 +1,77 @@
-int Pot; //Initialise la variable qui va recueillir la valeur du potentiomètre
+ /*
+ * Library: https://github.com/bolderflight/MPU9250
+Basic_I2C.ino
+Brian R Taylor
+brian.taylor@bolderflight.com
 
-// Moteur branché sur l'interface 3
+Copyright (c) 2017 Bolder Flight Systems
-int Moteur = 17;
 
-// Valeur pour le moteur (varie entre 0 et 255)
+Permission is hereby granted, free of charge, to any person obtaining a copy of this software 
-int Valeur_Moteur;
+and associated documentation files (the "Software"), to deal in the Software without restriction, 
+including without limitation the rights to use, copy, modify, merge, publish, distribute, 
+sublicense, and/or sell copies of the Software, and to permit persons to whom the Software is 
+furnished to do so, subject to the following conditions:
+
+The above copyright notice and this permission notice shall be included in all copies or 
+substantial portions of the Software.
+
+THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING 
+BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND 
+NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, 
+DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, 
+OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.
+*/
+/*
+ * Updated by Ahmad Shamshiri on July 09, 2018 for Robojax.com
+ * in Ajax, Ontario, Canada
+ * watch instrucion video for this code: 
+For this sketch you need to connect:
+VCC to 5V and GND to GND of Arduino
+SDA to A4 and SCL to A5
+
+S20A is 3.3V voltage regulator MIC5205-3.3BM5
+*/
+
+#include "MPU9250.h"
+
+float biai = 1.25;
+unsigned long previousTime;
+int interval = 300;
+int stepPin = 14;
+int dirPin = 12;
+bool pinState = LOW;
+// an MPU9250 object with the MPU-9250 sensor on I2C bus 0 with address 0x68
+MPU9250 IMU(Wire,0x68);
+int status;
 
 void setup() {
+  // serial to display data
+  Serial.begin(115200);
+  while(!Serial) {}
 
-Serial.begin(9600); //Initialise la communication entre le PC et Arduino
+  // start communication with IMU 
-pinMode(Moteur, OUTPUT);
+  status = IMU.begin();
+  if (status < 0) {
+    Serial.println("IMU initialization unsuccessful");
+    Serial.println("Check IMU wiring or try cycling power");
+    Serial.print("Status: ");
+    Serial.println(status);
+    while(1) {}
+  }
+  pinMode(stepPin,OUTPUT);
+  pinMode(dirPin,OUTPUT);
 }
 
 void loop() {
+  // read the sensor
+  digitalWrite(dirPin,HIGH);
+  IMU.readSensor();
+  // display the data
 
-//Lire la valeur du potentiomètre
+  if((micros() - previousTime) >= interval){
-Pot = analogRead(6);
+    previousTime = micros();
-
+    pinState = !pinState;
-//Affiche la valeur du potentiomètre sur le moniteur série
+    digitalWrite(stepPin,pinState);
-Serial.print("Potentiometre : "); Serial.println(Pot);
+    Serial.println(IMU.getAccelX_mss() + IMU.getAccelY_mss() + IMU.getAccelZ_mss() + biai +11);
-
+  }
-// Valeur min du potentiometre
+} 
-if (Pot < 1)
-{
-Pot = 0;
-}
-// Valeur max du potentiometre
-if (Pot > 8190)
-{
-Pot = 8191;
-}
-
-//Definir la valeur à envoyer au moteur : 184 => 0 et 873 => 255)
-Valeur_Moteur = map(Pot, 0, 8191, 0, 255);
-
-Serial.print("Moteur : "); Serial.println(Valeur_Moteur); //Affiche la valeur du potentiomètre sur le moniteur série
-
-// Envoie de la valeur de sortie au moteur
-analogWrite(Moteur, Valeur_Moteur);
-
-delay(200);
-
-}